WINE ENTHUSIAST N'FINITY PRO INSTRUCTION MANUAL Pdf Download (2024)

FAQs

How do I reset the temperature on my Wine Enthusiast wine cooler? ›

To set the temperature, press the up or down arrow button to increase or decrease the temperature setting until the desired temperature is attained. It may take some time to reach the set temperature. The temperature will fluctuate more so when the wine cellar is empty.

If your wine cooler is not cooling, it may be due to a broken evaporator. This may be a result of ice buildup. This element also has a fan, which may become dirty or blocked. To fix the problem, clean up any debris around the fan or component itself.

LL. LL flashes with buzzing alarm. This means the related compartment temperature is lower than 23F. Stop the wine cooler running until the ambient temperature rises. Don't use the wine cellar in a lower temperature environment than necessary.

This is a normal phenomenon, and the circulating fan inside the wine cooler will run with a certain regularity. Because the cold air is heavy, it will sink to the bottom of the wine cabinet. The circulating fan keeps running, so that the cold air is evenly distributed inside the wine cabinet.

For short-term storage, you want to avoid any pre-mature aging or agitation. To do this, a constant temperature of 50°-59° Fahrenheit is best. If you'll be storing your wine for longer, you'll want to keep your cooler a little colder—53° to 57° Fahrenheit.

If the temperature controls cannot be adjusted (keypads do not work), the Wine Chiller may be in lockout mode. Press the Red Wine key, if "LOC" appears in the display, the lockout mode is engaged. To exit, press the Red Wine and Interior Light pads simultaneously for 3 seconds.

Check the evaporator frequently to see if there's an ice buildup. If there is, thaw the ice and clean the coils. Ensure the blades of the evaporator's fan are not damaged so it can circulate the air properly, and the fridge will be able to chill the wine to the right temperature.

Resetting a refrigerated cellar is the best option if there doesn't appear to be anything wrong with the unit but it can't maintain the temperature properly. To reset, simply pull the plug out and leave it out for between 30-60 minutes. Keep the door closed and your currently stored wine will be largely unaffected.

A wine cooler is an excellent solution for storing most wines safely for a month or two. Just remember to take bold reds out of the cooler a good few hours before you want to drink them. It is important to allow them to gently come up to temperature and that takes time in a cool, dry place.

Generally the E4 error code is a result of a malfunctioning defrost sensor so that is why you have to manually defrost the unit. I can walk you through a more in-depth diagnosis of the issue, give instructions on how to do the repair and supply part numbers but will need the model of your cooler.

What is E4 error on wine cooler? ›

an E4 code is from the coil freezing and forming ice. That only happens if the unit is failing and low on freon, has a bad fan, or if the filters haven't been cleaned in some time restricting airflow to coil.

The wine cooler can be reset by disconnecting the electrical power for 5 mins and then turn it back on. After that the temperature set point can be adjusted on the control panel using the up and down arrows.

Place a damp towel or cloth inside the wine fridge. The moisture from the towel will evaporate into the air, raising humidity levels. Keep an eye on the towel's condition and replace it when it dries out.

With a warm cellar (72°F) on a warm day (85°F), the low side pressure would be 35-40 psi. The high side pressure would be 180-200 psi, with a subcooling of 4 degrees and a total superheat of 24 degrees. Given a 90-foot line set, the pre-weigh-in refrigerant charge should be 3.02 lbs.

Passive Humidity Control: Passive humidity control is the most basic method of regulating humidity in wine fridges. It involves adding a water tray to the fridge's base to increase the humidity levels naturally. The tray is filled with water, and the fan blows air over the water, increasing the humidity in the fridge.

The blinking blue light on your temperature control panel is an indication that the wine cooler is working in its most quiet mode and the internal fans are running at 75% of their maximum.

Press and hold the power button for one second to switch the wine cooler on. Press and hold the power button for five seconds to switch the wine cooler off. Press the up or down buttons until the required temperature is shown on the display. The preset temperature is 12˚C / 54˚F.

Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each depression of the buttons will scroll through the available temperature settings in increments or decrease of 1 degree Celsius. The temperature setting can be adjusted from 6℃ to 18℃.